Choosing a system
How do ducted air conditioning zones work?
Ducted zones let you choose which rooms receive air. Learn how zone switches, room sensors and bedroom airflow affect the way your family uses the system.

If the children need cool bedrooms at bedtime but the living room is empty, it makes sense to ask whether your ducted system can focus on the bedrooms. Zones let you choose which rooms receive heated or cooled air. How much control you have depends on the equipment and the way it is designed, so a quote that says “four zones” needs a little explanation.
What is a ducted air conditioning zone?
A ducted system sends air through ducts: enclosed passages that carry it to the grilles, or air outlets, in your rooms. A zone is one room or a group of rooms controlled together. For example, the kitchen and living room might share a zone, while the bedrooms form another.
Inside the ducts, motorised flaps called dampers open or close to control where the air goes. Turning a zone on allows air through to its rooms; turning it off normally closes that route. Some designs need to keep an area open so the system can move enough air, which we explain below. You are choosing where the system delivers air; you are not turning each room into a separate air conditioner.
Does every zone have its own temperature setting?
No. Basic zoning gives you on/off switches for different areas, usually with a shared temperature setting. A bedroom can be included or left out, but a separate zone switch does not by itself give that bedroom a separate temperature.
Some compatible systems can adjust the amount of air sent to an area. Others also use room sensors, which measure the temperature in particular rooms, and support different temperature settings for different zones. These features vary by model and controller, so ask which are included rather than relying on the number of zones.

How should you group the rooms?
Start with an ordinary day in your home. Which rooms do you use after work and school, and which need heating or cooling once everyone is in bed? Rooms that sit next to each other do not necessarily belong on the same switch.
As a hypothetical example, imagine a parent working in the study during the day, everyone gathering in the living room after school, then using only the bedrooms overnight. If the study shares a zone with an unused spare bedroom, both receive air whenever that zone is on. Showing that routine on a floor plan helps the installer see where separate control would be useful.
Can you run only one bedroom overnight?
Sometimes, but it needs to be checked before you buy. Every ducted system has an amount of air it needs to move, and a single small bedroom may not provide enough open outlets for the chosen equipment. Some designs keep another area open to handle that airflow; others have equipment and controls suited to smaller zones.
This matters if one child needs cooling while everyone else is comfortable. Ask the installer to confirm the smallest combination you can use and whether any other room must receive air at the same time. Do not assume that more zone buttons mean every bedroom can always run alone.

Why do sensors and closed doors matter?
The system needs a temperature reading to decide how much heating or cooling is needed. Depending on the setup, it may use a sensor at the controller, elsewhere in the system, or in individual zones. A reading from one part of the home may not describe another room well, so ask where the proposed system measures temperature and which reading it uses.
Sensor position matters too: air blowing directly onto a sensor or a nearby heat source can affect its reading. The installer should choose and configure the sensor locations for the equipment. A room sensor is useful only when the system can use that information in the way you expect.
Air also needs a way back from the rooms to the system. This is called the return-air path, and it allows the air to circulate. If your family sleeps with bedroom doors shut, tell the installer so they can check how air will return with those doors closed. You should not have to discover at bedtime that the design depends on doors being open.
What should you ask before accepting the quote?
You do not need to work out the duct design yourself. Ask the installer to show you how the proposed zones handle your usual routine, then have these details written down:
- Which rooms and outlets belong to each zone, using names your family will recognise.
- Whether each zone offers on/off control, airflow adjustment or its own temperature setting.
- Where temperature is measured and which sensors and controls are included.
- Which zones can run together, including the smallest overnight combination.
- How air returns when bedroom doors are in their usual position.
When the system is handed over, have the installer demonstrate those everyday settings on the controller. It is easier to remember “bedrooms overnight” when you have seen what to press and know which areas will receive air.
If you are planning ducted air conditioning, bring Caleb a floor plan or a list of the rooms you use together. Tell us about bedtime doors and any room that is often uncomfortable. We can help you understand the proposed zones and check what the equipment can do before you choose.
Sources and further reading
Research checked 5 October 2026. For operation, maintenance and installation requirements, use the instructions for the exact equipment in your home.
- Daikin — how motorised dampers control zones ↗
- ActronAir — zoning features vary by system ↗
- ActronAir — airflow and temperature control options ↗
- ActronAir — model-specific minimum airflow design guidance (PDF) ↗
- ActronAir — QUE sensor positioning and controls manual (PDF) ↗
- US Department of Energy — room return-air paths ↗
Want a hand with this?
List the rooms used together, especially at night. We can design zones around real life.
Ask Caleb ↗


